Auriou vs Bailey, hmmm

Posted by is9582 on March 4, 2016as , , , , , , , , , , , ,

Not long ago I was shifting from flattening the face side of my massive Soft Maple boards (8 1/2″ W x 3 3/4″ D x 75″ L), to one of the edge faces. On one board both of the edge faces were about equal in perceived work, as each had some twist and similar nasty rough characteristic. Many times I’d grab my old Bailey #6 hand plane set up with a decently cambered iron, and start with the iron way out there, just to expedite the process, as I hate just getting a whisker or two on a pass, at least at this stage. Oh, and I am talking about wood that I purchased that is basically rough, to the point where it has some fuzzy all over.

On this board, I reached for my #6 and I’m really not sure why my hand re-directed to my 9-grain Auriou Rasp, which is my medium grit, as I also have a 5-grain for really heavy stuff and a 15-grain model makers for the super fine work (Auriou rasps 1-grain – 4-grain are intended for working stone, while 5-grain – 15-grain are good for wood).


Here is the flat side of my  9-grain Auriou Rasp, on the rough edge face of the board.

Here is the flat side of my 9-grain Auriou Rasp, on the rough edge face of the board.


From my perspective, the far right corner of my board was elevated, as was the near left corner, as you’d expect when you have some wind/twist. I stood the board on it’s opposite side, with a wedge under one corner, to keep it from rocking (or at least too bad). I grabbed the 9-grain Auriou with it’s handle in my right hand and the tip in my left, and held it in an almost 45-degree position with my left hand leading the way. As I touched the wood, I tried to keep both of my hands at a similar level from the floor, and started near the far end of the board. Since I already knew the high area was on the right, it was easy to use that to confirm I was keeping my hands fairly level, as I expected to see wood removed on the right and nothing on the left, and the area removed shouldn’t slope to the right.

Since I’d never tried using my Auriou like this before, I made a couple of passes and then stopped to see if it was worth continuing, or if I was just wasting my energy. Surprisingly, this medium-grit rasp was rapidly bringing the high sections down, and as is somewhat usual for Auriou, it was leaving a very decent texture to the surface. I guess what I’m trying to say is that it wasn’t chewing it up and/or ripping it to shreds! With the positive results, I really got into it and gradually worked my way to the other end of the board.


Here is the same tool and board, and showing the progress from 2 or 3 passes with the rasp.

Here is the same tool and board, and showing the progress (see the red arrows) from 2 or 3 passes with the rasp.


After the I had all of the major high areas lowered down, I shifted over to my #6 hand plane, with it set at a much more reasonable bite, and rapidly completed this edge face. When I was done, I wondered if I might should’ve tried bringing in the 5-grain Auriou, but that bad boy was probably overkill, at least for this level of stock removal.



For those who haven’t yet had the chance to use any of the Auriou line of rasps, I’ll share a tip that I found during my time with these tools. I think my first tendency with a rasp (maybe just because I’m a guy, but I can’t say for sure) is to lean into it while applying pressure, to get the wood out of the way. While this tactic will certainly remove wood briskly, the overall surface can seem like a chainsaw hit it. I’ve found that using a light touch on the downward force, and controlled strokes can still rapidly remove wood, but ends up leaving a much better surface. This seems to go for any of the Auriou rasps I’ve used (the three I listed are all the cabinet maker’s shape, with one flat side and one that is curved from side-to-side, but I also have a 13-grain in their handle-maker’s style, that has the same side-to-side curve, but also curves on the long axis, towards the tip), so if you buy or are lucky enough to receive as a gift, try this to get the best results from your rasps. Oh, and Auriou make their rasps as either a right-hand or a left-hand rasp, based on how the teeth of the rasp are created. If you are a right-handed person, and are using a left-handed rasp, you’ll end up roughing the surface rather than the teeth actually cutting like they are intended. Just keep that in mind if you are buying one of their rasps, whether new or used.

I hope you’ve enjoyed the information and may give it a try as well. Please let me know if you have any questions or comments.

Lee Laird

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>